Quick Start of UI | Network Camera

Quick Start of UI for IP Camera

Connection Diagram

  1. Power on IP Camera and connect it to router via ethernet cable.

Tips: At the very beginning, it's strongly recommended to follow this instructions to connect the camera, especially for network segment issues.

Download & Install IPCManager

Download IPCManager

Download IPCManager

Device Manager Version
Suitable for
Windows
MAC
Windows
Windows
MAC

Install IPCManager

Installation by the following steps:
  1. Right click the application and run as administrator;
  2. Select the corresponding language from the drop-down list (English, Polish, Russian, Japanese, German, Simplified Chinese, Traditional Chinese are available for Windows. Only English for MAC version.) 
  3. Click Next-->Next-->Install

Download & Install ActiveX

Download ActiveX

Download ActiveX from the following link: IPCOCX4 version 4.3.0(HTML5).

Install ActiveX

Install ActiveX after downloading with administrator and restart your PC.

Configure IP via IPCManager

  1. Run IPCManager (If you already installed it)
  2. Enter username & password (admin & 12345 by default)
  3. Select the encoder you would like to set
  4. Click checkbox of DHCP-->Modification-->Close-->Refresh

Info
🧙Tips: please ensure the IP camera and your PC are on the same network segment if it’s connected to the same router. That’s why it’s recommended to use DHCP to obtain IP address to make it for sure.

Access Camera from a Browser

  1. Start a browser like IE, Chrome, Firefox (Chrome Recommended);
  2. Enter the IP address you configured above via IPCManager;
  3. Enter username (admin) and password (12345 by default);
  1. Click “Login” and the Live View page opens in your browser

Adjust Focus

  1. 1 means Zoom Out: long press until you think it ok.
  2. 2 means Zoom In: long press until you think it ok.
  3. 3 means Reset: reset to default focus if you wrongly zoom in/out.

Configure Parameters of Audio

  1. Go to Configuration-->Video & Audio-->Audio-->Audio 
  2. Click checkbox to “Enable audio”; Audio codec format set as “AAC”;
  3. Sampling rate set as “24000” or higher; 
  4. Input volume set as “39” or so(Reference Value: users can log into GUI and set sampling rate as 24000 or higher if better voice quality is required because the default sampling rate here is 8000.)

Configure Parameters of Video

  1. Go to Configuration-->Video & Audio-->Video-->Video 
  2. Bit rate set as 500(Reference Value: users can set higher bit rate to remove mosaic but it should be matched to your network bandwidth because of uplink bandwidth used.) 
  3. Key interval set as 10(Reference Value: users can set lower key interval to get better image quality.)

Configure RTMP Address

  1. Go to Configuration-->Network-->RTMP-->RTMP-->Enable(True) 
  2. Enter Push URL: copy Stream URL and Stream Key from YouTube Studio into column of Push URL below:

YouTube Studio

Go back to YouTube Studio after setting RTMP PUSH URL. After setting the RTMP PUSH URL for live streaming to YouTube, you can check if the stream is live in YouTube Studio. If the stream appears to have failed, consider the following steps for troubleshooting:
  1. Verify that the audio is enabled and set to use AAC encoding, as YouTube requires specific audio formats for live streaming.
  2. Confirm that the video encoding is set to H.264, as RTMP (Real-Time Messaging Protocol) doesn't support H.265 encoding.
  3. Verify that the bitrate is appropriately set. It may be necessary to adjust the bitrate, especially if it's initially set too high, as this can impact the streaming quality and stability.
  4. Check the default DNS settings to ensure they are available and functional, especially in the EU. Consider changing the DNS settings if needed.
  5. Verify that there's sufficient uploading bandwidth available for the live stream. If bandwidth is limited, adjusting the bitrate to a lower value can help ensure a more stable stream.
After performing these checks and adjustments, you can attempt to go back to YouTube Studio and verify if the live stream is successful. It's important to review the settings and configurations to ensure that all components are optimized for live streaming to YouTube.

    • Related Articles

    • Quick Start via IPCManager for IP Camera

      Connection Diagram Power on IP Camera and connect it to router via ethernet cable. Tips: At the very beginning, it's strongly recommended to follow this instructions to connect the camera, especially for network segment issues. Download & Install ...

    • Device Manager of IP Camera

      What's Device Manager? As for network camera, IPCManager is just one tool designed for below but not limited: Searching cameras in the attached network; Quickly modifying IP addresses in batch; Upgrading the latest firmware for cameras in batch; ...

    • IP Filter of IP Camera

      IP Filter Go to Configuration->Security->IP Filter This screen allows for the filtering of IP addresses, either blocking them, or granting them access to the camera. This feature helps make the camera more secure by limiting remote access only to ...

    • Upgrade Firmware for IP Camera

      Upgrade firmware via IPCManager Only Run IPCManager if you already installed it Enter username and password Go to Firmware Upgrading-->Add Online IPC Select the encoder and Browse the latest firmware Click "Upgrade" and it will start upgrading ...

    • Upgrade of IP Camera

      Upgrade Go to Configuration->System->Upgrade This menu allows the user to upgrade the camera’s firmware. Below is a screenshot of the Upgrade screen: NOTES There is model number notifications automatically, please make sure you have the right ...