Device of Router V519

Device of Router V519

Device

In this section, it allows the user to change the operation mode and language. Please check below details:

Operation Mode

  1. 5x operation modes can be selected: LTE Gateway (By Default), Gateway, 2.4G WISP, AP, Mix. Please see below photo:

LTE Gateway

By default, it’s LTE Gateway mode, all you have to do is to insert 3G/4G SIM card, then the router will auto recognize and register to the corresponding network of 3G/4G. You can also custom and select your ISP.

Gateway

When you’re ready to use “Gateway” mode (standard wireless router mode), the WAN port of router should be connected to the modem via ethernet cable to dial.

Obtain an IP address automatically

Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from browser again, and go to Network->LAN-> Select “DHCP” from dropdown list of Dial Mode ->Click “Confirm” and then the router will obtain an IP address automatically from ISP.

Manually Set IP

Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from browser again, and go to Network->LAN->Select “Static IP” from dropdown list of Dial Mode ->Enter IP address, Subnet Mask, Gateway, DNS and other parameters you get from ISP->Click “Confirm"

PPPoE

Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from browser again, and go to Network->LAN-> Select “PPPoE” from dropdown list of Dial Mode ->Enter username, password and other parameters you get from ISP->Click “Confirm".

2.4G WISP

Please go to System->Device->Operation Mode->2.4G WISP;
Click “Scan” and it’ll pop up one dialog window of all searched wireless network, select one and enter username, password if required to connect.

AP

Please go to System->Device->Operation Mode->Select “AP”->Confirm. Try to connect the WAN port of V519 to the LAN port of the primary router via ethernet cable, then it can turn your wired network into wireless network.
Info
🧙Tips:
  1. In AP mode, we need to connect our router A to the internet via a wired connection. Our router will then provide internet access to other devices through Wi-Fi or Ethernet ports, without assigning IP addresses to the connected devices. Instead, IP addresses are assigned by router A. It functions as a switch in this mode.
  2. In GATEWAY mode, we need to connect the WAN port of our router to router A via a wired connection. Our router will then provide internet access to other devices through Wi-Fi or Ethernet ports, while also assigning IP addresses to the connected devices.
It's important to note that in both AP and GATEWAY modes, the network segment of our router and router A should be different to avoid network issues and ensure proper functioning. Proper configuration is essential to ensure stable network connectivity for the connected devices.

Mix

In the Mix mode, it supports 4G, wired, wireless backup. When it’s failed to connect to network for main connection, the router will auto switch to the backup module to make sure the router can connect to the Internet normally.
  1. Go to System->Device->Operation Mode->Select “Mix”;
  2. After rebooting, go to Network->Connection->Set Main Connection as “LTE” and Alternate Connection as “WAN”:
  1. Enter the corresponding parameters, click “confirm” and the router will reboot;
  2. Insert SIM card and set parameters of 4G, and connected to 4G successfully;
  1. Set wireless connection and enter related parameters:
  1. Click “Interface” and you’ll see it’s all connected to 4G and WiFi:


    • Related Articles

    • Station List of Router V519

      Station List In this section, it allows the user to manage the online devices connected to this router. Please check below details:

    • Introduction of Router V519

      Brief Introduction Thank you so much for purchasing our 4G LTE industrial routers. V519-industrial 3G/4G router-adopts high performance 32-bit processor, high speed process protocol and large data, equipped with multiply 3G/4G industrial ...

    • Station Traffic Control of Router V519

      Station Traffic Control In this section, it allows the user to control the traffic for the assigned device connected to this router including download and upload. Please check below details:

    • FAQs: Upgrade of LTE Router V519

      LTE Router Upgrade Procedure via Telnet (Forced Upgrade Method) Download Toolkit LTE Router Upgrade Procedure via Telnet (Forced Upgrade Method) Preparation Steps: 1. Assign the IP address 192.168.8.10 to your computer. 2. Disable the firewall on ...

    • Station Address Bind of Router V519

      Station Address Bind In this section, it allows the user to bind the assigned IP with attached devices. After setting, it's necessary to restart the router to make it valid. Please check below details: